Laminator Parts

Replacement reverse cylinder for all ARL classic/squared profile and CSL/Classroom Series II roll laminators equipped with a manual reverse crank. May be listed as part number N015 in Owner's Manual.

Replacement blue heat switch wire for USI ARL and CSL/Classroom roll laminating machines requiring a female quick disconnect terminal on both ends. Wires are sold individually and feature two female quick connect terminals. Note: for machines requiring wires with one ring terminal and one female quick disconnect terminal, see item 3934.

Replacement blue heat switch wire for USI ARL and CSL/Classroom roll laminating machines requiring a female quick disconnect terminal on one end and a ring terminal on the other end. Wires are sold individually and feature one ring terminal and one female quick connect terminal. Note: for machines requiring wires with two female quick disconnect terminals, see item 3933.

Replacement motor drive switch for all classic/squared profile USI ARL roll laminators equipped with a variable speed motor. May be listed as part number 800PVSR or A3936 in Owner's Manual.

Replacement heat guard for all USI ARL and CSL/Classroom 27" roll laminators. May be listed as part number 512B or A3937 in Owner's Manual.

Replacement plastic deflector for all 27" classic/squared profile USI ARL and CSL/Classroom Series III roll laminating machines. May be listed as part number 715C or A3940 in Owner's Manual.

Replacement left side panel frame assembly for all gray CSL/Classroom Series III and classic/squared profile USI ARL laminating machines except Digital model. Complete side panel frame including all brackets, and hardware. May be listed as part number 900DSA in Owner's Manual.

Replacement right side panel frame assembly for all gray CSL/Classroom Series III and classic/squared profile USI ARL laminating machines except Digital model. Complete side panel frame including all brackets, and hardware. May be listed as part number 901DSA in Owner's Manual.

Film threading board for roll laminators. For all USI ARL and Classroom series machines. Can work with most machines and is easily cut-down if too wide for your specific machine.

Replacement idler roller for all 18" ARL Series roll laminators. May be used as upper or lower. Does not include dowel pins or nylon idler washers. May be listed as part number 013B or A4658 in Owner's Manual.

Replacement reinforcing bar for all 27" ARL and CSL/Classroom Series roll laminators except ARLPro2700. May be used as upper or lower, does not include mounting hardware. May be listed as part number 616B or A3993 in Owner's Manual.

Upper 1" diameter supply mandrel for all 12" USI ARL Roll laminating machines. May be listed as part number 907B or A4627 in Owner's Manual.

Lower 1" diameter supply mandrel for all 12" USI ARL Roll laminating machines. May be listed as part number 907B or A4628 in Owner's Manual.

Replacement digital temperature control board for all USI ARL Series Digital roll laminators except machines with the following serial number sequences: 0****-****, 1****-****, 4****-****, 5****-****, 9****-****, G****-****, or W****-****.

Replacement thermistor assembly for all USI ARL Series Digital roll laminators except machines with the following serial number sequences: 0****-****, 1****-****, 4****-****, 5****-****, 9****-****, G****-****, or W****-****.

Replacement jones socket for ARL Series roll laminators. Depending on machine model, part may be used for foot switch or fan kit applications. May be listed as part number N029 or A5096 in Owner's Manual.

Replacement motor control PC board. Fits all ARL Series 120 Volt roll laminators equipped with variable speed motor. For classic/squared profile ARL roll laminators with serial numbers 9252-999 or lower see item 4764. May be listed as part number N020 or A6101 in Owner's Manual.

Replacement heat guard for all USI ARL Series 18" roll laminators. May be listed as part number 512B or A4662 in Owner's Manual.

Replacement 18", 120V AC, 800 Watt heater cartridge for all USI ARL Series 18" roll laminators. May be listed as part number 517P or A4729 in Owner's Manual.

Replacement upper roller shaft. Fits all 18" ARL Series roll laminators. Can be used with upper laminating (front) or pull (rear) roller. May be listed as part number 101B or A4659 in Owner's Manual.

Replacement complete feed table assembly for all USI ARL Series 12"> roll laminators. Includes feed table, guide and guide hardware. May be listed as part number 900C in Owner's Manual.

Replacement heat guard for all USI ARL Series 12"> roll laminators. May be listed as part number 512B or A4611 in Owner's Manual.

Replacement upper roller shaft. Fits all 12"> ARL Series roll laminators. Can be used with upper laminating (front) or pull (rear) roller. May be listed as part number 101B or A5728 in Owner's Manual.

Replacement lower roller shaft for 12"> USI ARL Series roll laminators. May be used as lower laminating (front) or pull (rear) roller. Note: may be used as lower laminating (front) only on machines equipped with manual reverse crank. May be listed as part number 102B or A5729 in Owner's Manual.

Replacement upper heat shoe for all 12"> USI ARL Series laminating machines. Does not include heater, thermostat or mounting hardware. May be listed as part number 515C in Owner's Manual.

Replacement lower heat shoe for all 12"> ARL Series laminating machines equipped with thermoswitch; not compatible with digital type thermostats. Does not include heater, thermostat or mounting hardware. May be listed as part number 516C in Owner's Manual.

Replacement upper heat shoe for all 18" USI ARL Series laminating machines. Does not include heater, thermostat or mounting hardware. May be listed as part number 515C in Owner's Manual.

Replacement lower heat shoe for all 18" USI ARL Series laminating machines equipped with thermoswitch; not compatible with digital type thermostats. Does not contain heater, thermostat or mounting hardware. May be listed as part number 516C in Owner's Manual.

Replacement control knob for ARL and CSL/Classroom roll laminators. May be used as speed control knob on ARL Series machines equipped with variable speed motor, heat control knob on ARL Digital Series machines, or heat control knob on CSL/Classroom Series III and CSL/Classroom machines with new/round profile. May be listed as part number N021 or A5846 in Owner's Manual.

Key lock kit for all classic/squared profile ARL Series roll laminators. Includes grey left side housing with key lock installed.