Single speed AC gearmotor for classic/squared profile USI ARL and CSL/Classroom Series II roll laminating machines with preset, non-variable speed. May be listed as part number 300P or A0907 in Owner's Manual.

Note: part shown in photo is for identification purposes, appearance of actual service part may vary.

Replacement non-lighted rocker switch for all USI ARL classic/squared profile and CSL/Classroom Series II roll laminators equipped with single speed drive motors. Can be used as heat switch or drive switch; switch only, wires not included. If wires are required when using as a heat switch, see item number 3933. May be listed as part number 800P in Owner's Manual.

Replacement 25" rubber roller for 25" ARL and Series II and III CSL/Classroom roll laminators. Can be used as laminating (front) or pull (rear) roller. May be listed as part number 100C or A4556 in Owner's Manual.

Replacement plastic deflector for 25" ARL and Series III CSL/Classroom roll laminators. May be listed as part number 715C or A4565 in Owner's Manual.

Heat switch kit with wires for all CSL/Classroom Series II and III roll laminators and classic/squared profile ARL roll laminators equipped with single speed drive motor and non-lighted heat switch. Kit includes one non-lighted rocker switch and two switch wires.

Heat switch kit with wires for all classic/squared profile ARL roll laminators equipped with variable speed drive motor and lighted heat power switch. Kit includes one lighted rocker switch and three switch wires.

Replacement 120 Volt, 768 Watt heater cartridge for 25" ARL classic/squared profile and CSL/Classroom Series II and III roll laminating machines. May be listed as part number 517P in Owner's Manual.

Replacement upper 1" diameter supply mandrel for all 18" ARL roll laminating machines. May be listed as part number 907B or A4577 in Owner's Manual.

Lighted heat switch for all USI ARL classic/squared profile roll laminating machines equipped with variable speed motor. Switch wires not included; if switch wires are required see item number 3933.

Replacement lower 1" diameter supply mandrel for all 18" ARL roll laminating machines. May be listed as part number 907B or A4578 in Owner's Manual.

Replacement upper 1" diameter supply mandrel for all 25" ARL Series and 25" CSL/Classroom Series II and III roll laminating machines. May be listed as part number 907B or A4575 in Owner's Manual.

Replacement lower 1" diameter supply mandrel for all 25" ARL Series and 25" CSL/Classroom Series II and III roll laminating machines. May be listed as part number 907B or A4576 in Owner's Manual.

Complete replacement feed table assembly including feed table and feed guide with knob, screw and washer. Fits USI 25" ARL and CSL/Classroom Series II and III roll laminating machines. May be listed as part number 900C in Owner's Manual.

Complete replacement feed table assembly including feed table and feed guide with knob, screw and washer. Fits USI 18" ARL laminating machines. May be listed as part number 900C in Owner's Manual.

Variable speed 90VDC gearmotor for USI ARL Series roll laminating machines. May be listed as part number 300PVSR or A3225 in Owner's Manual. Does not fit machines with the following serial number sequences: 0****-****, 1****-****, 4****-****, 5****-****, 9****-****, G****-****, W****-****, or machines with serial numbers beginning with ">H.">

Replacement idler roller for all 12"> ARL laminating machines; may be used as upper or lower. Note: does not include dowel pins or nylon idler washers. May be listed as part number 013B in Owner's Manual.

Replacement idler roller dowel pin for USI ARL and CSL/Classroom Series roll laminating machines. Does not fit machines with the following serial number sequences: 0****-****, 1****-****, 4****-****, 5****-****, 9****-****, G****-****, or W****-****. May be listed as part number 014A or A4552 in Owner's Manual.

Replacement idler roller for 25" ARL and CSL/Classroom Series I, II, and III laminating machines, may be used as upper or lower. Note: does not include dowel pins or nylon idler washers. May be listed as part number 013B in Owner's Manual.

Replacement 23 tooth motor drive output sprocket for machines equipped with footage counter. Fits all ARL and CSL/Classroom Series roll laminating machines except CSL/Classroom Series I. May be listed as part number 301P or A3874 in Owner's Manual.

Replacement 19 tooth pull roll sprocket for roll laminators. Fits all ARL and CSL/Classroom Series roll laminating machines except CSL/Classroom Series I. May be listed as part number 303P or A3876 in Owner's Manual.

Replacement pressure adjustment plate for all classic/squared profile USI ARL and CSL/Classroom Series III roll laminating machines. May be listed as part number 400B in Owner's Manual.

Replacement pressure adjustment bracket for all ARL and CSL/Classroom series roll laminators except CSL/Classroom Series I and does not fit machines with the following serial number sequences: 0****-****, 1****-****, 4****-****, 5****-****, 9****-****, G****-****, W****-****, or machines with with serial numbers beginning with ">H."> May be listed as part number 401B or A3881 in Owner's Manual.

Replacement pressure adjustment spring. Fits all ARL and CSL/Classroom Series roll laminating machines except CSL/Classroom Series I. May be listed as part number 402P or A3882 in Owner's Manual.

Replacement pressure adjustment screw for all ARL and CSL/Classroom series roll laminators except CSL/Classroom Series I and does not fit machines with the following serial number sequences: 0****-****, 1****-****, 4****-****, 5****-****, 9****-****, G****-****, W****-****, or machines with with serial numbers beginning with ">H."> May be listed as part number 403B or A3883 in Owner's Manual.

Replacement upper roller bushing. Fits all ARL and CSL/Classroom Series roll laminating machines except ARL4000, ARL4000Pro, and CSL/Classroom Series I. Note: only use as upper pull roller bushing on ARLPro2700. May be listed as part number 404B or A3884 in Owner's Manual.

Replacement lower roller bushing. Fits all ARL and CSL/Classroom Series roll laminating machines except ARL4000, ARL4000Pro, and CSL/Classroom Series I. Note: only use as lower pull roller bushing on ARLPro2700. May be listed as part number 405B or A3885 in Owner's Manual.

Replacement heat shoe mounting bracket. Fits all ARL and CSL/Classroom Series roll laminating machines except ARL4000, and CSL/Classroom Series I. May be listed as part number 505B or A3886 in Owner's Manual.

Replacement upper heat shoe spacer for all ARL and CSL/Classroom 25" and 27" heat shoe roll laminators except CSL/Classroom Series I and ARL4000. May be listed as part number 507P or A3887 in Owner's Manual.

Replacement lower heat shoe spacer for all ARL and CSL/Classroom 25" and 27" heat shoe roll laminators except CSL/Classroom Series I and ARL4000. May be listed as part number 506P or A3888 in Owner's Manual.

Replacement heat guard for all 25" ARL and CSL/Classroom Series II, and III laminating machines. May be listed as part number 512B in Owner's Manual.