This dual-adhesive film features low-melt DigiSeal® adhesive on one side and a permanent pressure-sensitive adhesive with release liner on the other side. The pressure-sensitive backing is aggressive enough to adhere to most substrates.

Each white foam board is coated with a heat-activated adhesive and a 5mil film-laminate hinged at the top edge to form a pouch. To mount and laminate, slide a print between the film and board, then feed it through the laminator. Gloss finish. Additional color, sizes and finishes also available. Contains Box of 10 Boards

Sell Sheet USI ProMount Pouch Board

Create stickers or self-adhesive signs and posters in seconds with this dual adhesive film. One side permanently adheres to the back of print while the other features a pressure-sensitive adhesive covered by a release liner.

"Premium general purpose white mounting film. Features single release liner. Two-sided high peel adhesive with a good tack. Water-based acrylic adhesive.
"

Premium general purpose clear mounting film. Features single release liner. Two-sided high peel adhesive with a good tack. Water-based acrylic adhesive.

Each foam board is coated with a heat-activated adhesive and a 5mil film-laminate hinged at the top edge to form a pouch. To mount and laminate, slide a print between the film and board, then feed it through the laminator. Satin Finish. Additional color, sizes and finishes also available. Contains Box of 10 Boards

Sell Sheet USI ProMount Pouch Board with Satin Film

Self Adhesive Pouch Boards are self stick boards with attached gloss or matte laminate film. Use Self Adhesive Pouch Boards for mounting and laminating prints in one process. With the laminate pre-attached smoothly at the leading edge of the board, no set-up is required. You will achieve fast, consistent and professional laminating results. Great for on-demand and small runs of less than 10 prints. Can be used in any roll laminator or applied by hand. For sizes larger than 12"x18" we recommend using a laminator. Features include:

• 3/16" thick white gator board
• Permanent adhesive both on the board and laminate sheet to allow flush trimming
• 1/4" leading edge where film is attached to the self-stick board
• One piece construction let's you know your costs
• Easy to use in any Laminator
• 10 pouch boards per boxVJ42XLKB

Sell Sheet USI Self-Adhesive Gator Pouch Board

Each white ProMountCor foam board is coated with a heat-activated adhesive and a 5mil film laminate hinged at the top edge to form a pouch. Available in  satin and gloss finishes. To mount and laminate, slide a print between the film and board, then feed it through the laminator. ProMountCor is made of 3/16" white, dense, foam board coated with heat-activated adhesive. ProMountCor's adhesive forms a strong, permanent bond in the press as it reaches its low 130°F bonding temperature making it safe to mount: all digital printing, toner copiers, laser, plotters, water borne, solvent, UV and latex inkjet, resin coated and digital photo papers, posters and prints, synthetic papers and substrates, and polyester encapsulated charts and maps. Its permanent bond also means no edge lift when removed from the press, no mess, and it is perfect for bonding using multiple bites in a mechanical press. No removable HA board offers that option. It offers the lowest bonding temperature of any heat activated board available. Its specially formulated neutral pH adhesive is stable, inert and has revolutionized the industry with its dependable 130°F (54°C) low temperature/short dwell bond time in mount presses. ProMountCor aggressively mounts all porous papers, photographs, and previously heat sensitive digitals in dry mount presses or rollers. This makes it the perfect choice for both long term picture framing and short term sign/display mounting applications.

Sell Sheet USI ProMountCor Adhesive Board with Satin Film

Self Adhesive Pouch Boards are self stick boards with attached gloss or matte laminate film. Use Self Adhesive Pouch Boards for mounting and laminating prints in one process. With the laminate pre-attached smoothly at the leading edge of the board, no set-up is required. You will achieve fast, consistent and professional laminating results. Great for on-demand and small runs of less than 10 prints. Can be used in any roll laminator or applied by hand. For sizes larger than 12"x18" we recommend using a laminator. Features include:

• 4 mm thick white corrugated plastic board
• Permanent short term outdoor adhesive both on the board and laminate sheet to allow flush trimming
• 1/4" leading edge where film is attached to the self-stick board
• One piece construction let's you know your costs
• Easy to use in any Laminator
• 10 pouch boards per boxVJ42XLKB

Each foam board is coated with a heat-activated adhesive and a 5mil film-laminate hinged at the top edge to form a pouch. To mount and laminate, slide a print between the film and board, then feed it through the laminator. Luster (matte) finish. Additional color, sizes and finishes also available. Contains Box of 10 Boards

Sell Sheet USI ProMount Pouch Board with Luster Film

Each white ProMountCor foam board is coated with a heat-activated adhesive and a 5mil film laminate hinged at the top edge to form a pouch. Available in gloss, satin and luster finishes. To mount and laminate, slide a print between the film and board, then feed it through the laminator. ProMountCor is made of 3/16" white, dense, foam board coated with heat-activated adhesive. ProMountCor's adhesive forms a strong, permanent bond in the press as it reaches its low 130°F bonding temperature making it safe to mount: all digital printing, toner copiers, laser, plotters, water borne, solvent, UV and latex inkjet, resin coated and digital photo papers, posters and prints, synthetic papers and substrates, and polyester encapsulated charts and maps. Its permanent bond also means no edge lift when removed from the press, no mess, and it is perfect for bonding using multiple bites in a mechanical press. No removable HA board offers that option. It offers the lowest bonding temperature of any heat activated board available. Its specially formulated neutral pH adhesive is stable, inert and has revolutionized the industry with its dependable 130°F (54°C) low temperature/short dwell bond time in mount presses. ProMountCor aggressively mounts all porous papers, photographs, and previously heat sensitive digitals in dry mount presses or rollers. This makes it the perfect choice for both long term picture framing and short term sign/display mounting applications.

Optically clear mounting adhesive. Features double release liner with permanent adhesive on both sides. Great for applications requiring see-through graphics

Self Adhesive Pouch Boards are self stick boards with attached gloss or matte laminate film. Use Self Adhesive Pouch Boards for mounting and laminating prints in one process. With the laminate pre-attached smoothly at the leading edge of the board, no set-up is required. You will achieve fast, consistent and professional laminating results. Great for on-demand and small runs of less than 10 prints. Can be used in any roll laminator or applied by hand. For sizes larger than 12"x18" we recommend using a laminator. Features include:

• 3/16" thick white foam board
• Permanent adhesive both on the board and laminate sheet to allow flush trimming
• 1/4" leading edge where film is attached to the self-stick board
• One piece construction let's you know your costs
• Easy to use in any Laminator
• 10 pouch boards per box

Sell Sheet USI Foam Board Self-Adhesive Pouch Board

ProMountCor is made of 3/16" white, dense, foam board coated with heat-activated adhesive. ProMountCor's adhesive forms a strong, permanent bond in the press as it reaches its low 130°F bonding temperature making it safe to mount: all digital printing, toner copiers, laser, plotters, water borne, solvent, UV and latex inkjet, resin coated and digital photo papers, posters and prints, synthetic papers and substrates, and polyester encapsulated charts and maps. Its permanent bond also means no edge lift when removed from the press, no mess, and it is perfect for bonding using multiple bites in a mechanical press. No removable HA board offers that option. It offers the lowest bonding temperature of any heat activated board available. Its specially formulated neutral pH adhesive is stable, inert and has revolutionized the industry with its dependable 130°F (54°C) low temperature/short dwell bond time in mount presses. ProMountCor aggressively mounts all porous papers, photographs, and previously heat sensitive digitals in dry mount presses or rollers. This makes it the perfect choice for both long term picture framing and short term sign/display mounting applications.

Sell Sheet ProMountCor Adhesive Board with Gloss Film