Replacement temperature display PC board for MRL42 roll laminator equipped with LCD display. Note: if retrofitting to machine originally equipped with LED temperature display PC board, the main heat control PC board must also be replaced to be LCD compatible, see item 0651.

Replacement temperature display bezel/lens for all MRL42 roll laminators equipped with LCD temperature display PC board. Includes one bezel and one lens.

Replacement thermal cut-off for MRL42 roll laminator. May be used in upper or lower heat shoe.

Replacement motor control PC board for MRL series roll laminators. PC board only, does not include noise suppression capacitor; see item 0616 for capacitor.

Replacement double pole main power switch for MRL Series roll laminators.

Replacement supply mandrel end cap for 2 1/4 supply mandrel; "round" end. Fits CSL/Classroom Series II roll laminators and MRL42 waste rewind mandrel.

Replacement supply mandrel end cap for 2 1/4 supply mandrel; "square" end. Fits CSL/Classroom Series II roll laminators and MRL42 waste rewind mandrel.

Feed guide fastener kit includes knurled head screw and tinnerman nut. For use on ARL and CSL/Classroom machines equipped with a formed steel feed table.

Feed guide fastener kit includes knob, hex head screw and lock washer. For use on machines equipped with an anodized aluminum feed table.

Replacement fuse holder for MRL Series 30 Amp main fuses.

Replacement 30 Amp main fuse for MRL42 roll laminators.

Replacement drive motor for MRL series roll laminators.

Replacement waste rewind/take-up mandrel for MRL42 roll laminator

Shipping carton with foam inserts for USI ProMount™ 2700 Plus

Shipping carton with foam inserts for classic/squared profile ARL25 or CSL/Classroom 25 Series III roll laminating machines.

Single speed AC gearmotor for classic/squared profile USI ARL and CSL/Classroom Series II roll laminating machines with preset, non-variable speed. May be listed as part number 300P or A0907 in Owner's Manual.

Note: part shown in photo is for identification purposes, appearance of actual service part may vary.

Replacement motor control PC board. Fits all ARL Series 120 Volt roll laminators equipped with variable speed motor. For classic/squared profile ARL roll laminators with serial numbers 9252-999 or lower see item 4764. May be listed as part number N020 or A6101 in Owner's Manual.

Replacement friction disk. Fits all USI ARL and CSL/Classroom Series roll laminators except CSL/Classroom Series I. May be used as upper or lower. May be listed as part number 906B or A5104 in Owner's Manual.

Replacement heat guard for all USI ARL Series 18" roll laminators. May be listed as part number 512B or A4662 in Owner's Manual.

Replacement 18", 120V AC, 800 Watt heater cartridge for all USI ARL Series 18" roll laminators. May be listed as part number 517P or A4729 in Owner's Manual.

Replacement upper roller shaft. Fits all 18" ARL Series roll laminators. Can be used with upper laminating (front) or pull (rear) roller. May be listed as part number 101B or A4659 in Owner's Manual.

Replacement complete feed table assembly for all USI ARL Series 12"> roll laminators. Includes feed table, guide and guide hardware. May be listed as part number 900C in Owner's Manual.

Replacement heat guard for all USI ARL Series 12"> roll laminators. May be listed as part number 512B or A4611 in Owner's Manual.

Replacement upper roller shaft. Fits all 12"> ARL Series roll laminators. Can be used with upper laminating (front) or pull (rear) roller. May be listed as part number 101B or A5728 in Owner's Manual.

Replacement lower roller shaft for 12"> USI ARL Series roll laminators. May be used as lower laminating (front) or pull (rear) roller. Note: may be used as lower laminating (front) only on machines equipped with manual reverse crank. May be listed as part number 102B or A5729 in Owner's Manual.

Replacement upper heat shoe for all 12"> USI ARL Series laminating machines. Does not include heater, thermostat or mounting hardware. May be listed as part number 515C in Owner's Manual.

Replacement lower heat shoe for all 12"> ARL Series laminating machines equipped with thermoswitch; not compatible with digital type thermostats. Does not include heater, thermostat or mounting hardware. May be listed as part number 516C in Owner's Manual.

Replacement upper heat shoe for all 18" USI ARL Series laminating machines. Does not include heater, thermostat or mounting hardware. May be listed as part number 515C in Owner's Manual.

Replacement lower heat shoe for all 18" USI ARL Series laminating machines equipped with thermoswitch; not compatible with digital type thermostats. Does not contain heater, thermostat or mounting hardware. May be listed as part number 516C in Owner's Manual.

Heater assembly for USI 31" roll laminating machine. Equivalent part number: 800ELX